Tyco F3200 Bedienungsanleitung Seite 56
- Seite / 284
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
F3200 Installation & Programming Manual Document No: LT0122
Configuring a FIP
Page 5-2 5 July 2001 Issue 2.7
5.1 GENERAL
An F3200 FIP is configured to suit a particular customer's requirements by:
Fitting and connecting the required pcb modules;
adding appropriate battery test resistors when necessary;
adjusting or removing links on the pcbs;
programming the FIP.
The detectors, manual call points (MCPs), warning devices, ancillary equipment and field
wiring that are connected to the FIP must match the FIP configuration.
The FIP configuration data, which is entered during programming, is stored in the non-
volatile memory database. The database may be saved to a computer for backup storage,
or reloaded from a computer.
All programmable options have a default option for the most likely usage. That is, for many
applications, no programming other than entry of site and zone names will be necessary.
Programming is described in detail in Chapters 6, 7, 11 and 12. The rest of this chapter
describes configuration of the hardware.
5.2 MODULE CONFIGURATION
The required modules are fitted to the F3200 as described in Section 2.3.2. Note that 8 way
modules are connected Bus Out to Bus In with all 8 Zone Modules preceding any 8 Relay
Modules. (Refer also to Section 8.1.3).
The F3200 does various self-tests on start up and includes checking to see what modules
are present (including 16 Zone LED Display Bds). It displays the results on the LCD. If the
modules present do not agree with the programmed database then the FIP annunciates this
and remains inactive.
E2 Initialisation causes the Controller/Display to accept the modules found as present and
stores this configuration in the database. E2 Initialisation also clears all other data
programmed in the database. Refer to Section 6.3.1.
Where it is desired to add a module to an existing system this can be done by programming
the Module Configuration through the keyboard (see Section 7.1).
For servicing, modules can be temporarily removed as detailed in Section 10.2 of the
Operator's Manual. This temporary configuration is not stored in the database.
- FIRE INDICATOR PANEL 1
- END USER LIABILITY DISCLAIMER 2
- TABLE OF CONTENTS 3
- AMENDMENTS 5
- CHAPTER 1 7
- INTRODUCTION 7
- 1.1 SCOPE 8
- 1.2 ASSOCIATED DOCUMENTATION 9
- 1.3 PRODUCT HISTORY LOG 10
- 1.5 GLOSSARY OF TERMINOLOGY 13
- Introduction 14
- CHAPTER 2 15
- SYSTEM DESCRIPTION 15
- 2.1 OVERVIEW 16
- System Description 17
- FIG 2.1.1 17
- FIG 2.1.2 18
- F3200 OPERATOR DISPLAY PANEL 18
- FIG 2.1.3 19
- F3200 - SMALL CABINET 19
- 2.2 PHYSICAL STRUCTURE 21
- FIG 2.2.2 23
- 2.3 SYSTEM STRUCTURE 24
- SYSTEM SPECIFICATIONS 29
- CHAPTER 3 29
- 3.1 GENERAL 30
- 3.2 MECHANICAL SPECIFICATIONS 31
- 3.3 ELECTRICAL SPECIFICATIONS 32
- 3.4 INPUT SPECIFICATIONS 36
- 3.5 OUTPUT SPECIFICATIONS 42
- 3.6 CONTROLS 47
- 3.7 DISPLAYS 48
- CHAPTER 4 49
- ORDERING INFORMATION 49
- 4.1 ORDERING INFORMATION 50
- CHAPTER 5 55
- CONFIGURING A FIP 55
- 5.1 GENERAL 56
- 5.2 MODULE CONFIGURATION 56
- 5.4 LINKS ON PCB MODULES 65
- CHAPTER 6 67
- PROGRAMMING 67
- 6.1 INTRODUCTION 68
- FUNCTIONS 78
- DATABASE 79
- PARAMETERS 83
- Programming 102
- CHAPTER 7 103
- 7.3 CONFIGURING ZONES 113
- 7.4 PROGRAMMING OUTPUTS 115
- 7.5 RELAY SUPERVISION 135
- INSTALLATION & WIRING 139
- CHAPTER 8 139
- 8.1 INSTALLATION 140
- 8.2 FIELD WIRING 146
- 8.3 AZC WIRING 148
- Installation & Wiring 149
- FIG 8.3.3 149
- 8.5 WARNING SYSTEM WIRING 153
- FIRE PANEL 155
- 8.6 MODULE RELAY WIRING 158
- 8.7 OPEN COLLECTOR WIRING 160
- 8.9 RDU WIRING 162
- FIG 8.8.1 163
- EXAMPLE OF RDU COMS WIRING 163
- CHAPTER 9 165
- APPLICATIONS 165
- CONFIDENTIAL: 173
- CONTROL MODULE (CCT 1) 173
- SYSTEM/CIRCUIT DIAGRAM 173
- 1.111 PA07261945-1-1A3 173
- CONTROL MODULE (CCT 2) 174
- 1.111 PA07271945-1-2A3 174
- CONTROL MODULE (CCT 3) 175
- 1.111 PA07281945-1-3A3 175
- CONTROL MODULE (CCT 4) 176
- 1.111 PA07281945-1-4A3 176
- 9.2 GAS FLOOD 177
- Applications 183
- FIGURE 9.2.1 183
- GAS FLOOD LOGIC DIAGRAM 183
- FIG 9.2.2 184
- 9.3 SUB FIP MONITORING 189
- (EXPLOSIVE ATMOSPHERES) 192
- * EOL to suit Panel 198
- ZAU401 (Rev 2) 203
- (PA0838) 203
- CHAPTER 10 205
- ALIGNMENT, ADJUSTMENT & 205
- PLACING INTO OPERATION 205
- 10.2 PLACING INTO OPERATION 207
- CHAPTER 11 211
- NETWORK PROGRAMMING 211
- 11.1 INTRODUCTION 212
- 11.2 PROGRAMMING METHODS 214
- TX RLY CTRLS 215
- 11.4 SID CONFIGURATION 222
- 11.6 NET COMMANDS 225
- 11.7 NET FFCIF CONFIGURATION 226
- 11.9 NETWORK LOGIC VARIABLES 230
- 11.10 NET STATUS REFRESH 231
- 11.11 NDU OPERATION 232
- Network Programming 236
- CHAPTER 12 237
- NEW ZEALAND OPERATION 237
- 12.1 GENERAL 238
- 12.3 MANUAL CALLPOINT (MCP) 240
- 12.4 PROGRAMMABLE OPTIONS 241
- 12.5 LOGIC TOKENS 242
- New Zealand Operation 249
- NDU Cabinet 250
- Picture Frame Display Cabinet 251
- FIG 12.8.4 252
- CHAPTER 13 255
- TANDEM LCD MODE 255
- 13.1 TANDEM LCD MODE 256
- APPENDIX A1 257
- APPENDIX A2 262
- Appendix A 265
- Table IV TYCO Detector Range 265
- APPENDIX B 267
- Appendix B 268
- THIS PAGE INTENTIONALLY BLANK 268
- REF: 269
- FUNCTION & LOGIC EQUATION 276
- & LOGIC EQUATIONS 278
- DEISOLATE/RESET EQUATIONS 281
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Tyco F3200
(24 Seiten)Sylvania 6265FC manuali
Manuali dei proprietari e guide per l'utente per Videoregistratori Sylvania 6265FC.
We fornisce 1 manuali pdf Sylvania 6265FC per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Kommentare zu diesen Handbüchern